Phase 2 of 6 · in flight

The Mud Kitchen

Phase II of the corner: a mud kitchen counter and a low sensory table for five drop-in stainless pans, drawn to scale with cut lists and a bill of materials before anything gets cut.

Built from an @happilees_ reel · dimensions worked back from video frames · drawn Aug 3, 2026

I found the layout in a reel and worked the dimensions back out of the video frames, because the creator never published plans. Two freestanding pieces, both plain dimensional-lumber butt-joint construction: chunky 4×4 legs, 2×6 frames, plank tops, exterior screws. Every cut is a straight crosscut on the miter saw except the sink circle and the five pan openings, which are jigsaw work. The overbuilt framing is why it reads as solid on camera, and it is.

ModuleWhat it isFootprintHeight
AMud kitchen counterCounter with faux stove, inset bowl sink, low shelf, slat backsplash wall with cap ledge + cup hooks96" × ~26"22" counter / 47" overall
BSensory pan tableLow table with 5 drop-in stainless steam-table (GN ½) pans for rocks, sticks, water, mud82" × 17"18"
CCorner bench (optional)Low chunky bench/step that closes the L, doubles as seat and work surface48" × 17"12"
Sizing assumption: counter at 22" and table at 18" fit roughly ages 2–6. A pure toddler build drops to 18"/14"; bigger kids go to 24"/20". Only the leg cut lengths change, nothing else in the BOM moves.

1 · Layout

Plan · the layout in the reel

house wall or fence (backsplash can also stand free)A · mud kitchen counter96" × 26" · counter 22" high≈ 30" clear — two kids pass each otherB · sensory pan table — 82" × 17" · 18" highC · bench 48" × 17"12" high96"26"82¼"
Counter against the wall, the low pan table parallel in front, the optional bench closing the L on the left. About 30" between A and B.

2 · Module A: the mud kitchen counter

Module A · front elevation

96" (8-ft boards, no rips)22" counter47" overall4 × 2×6 slats2×8 cap ledge (display shelf)brass cup hooks every ~6" + S-hooksslat wall screwed to rear posts2×8 top, 3 boards2×6 apron"stove" knobs: wood rounds painted black2×6 stretcher + 2×6 low shelf4×4 legsmini shelf for jars
Three leg pairs, ends and middle, so the 8-ft span doesn't sag. The slat wall starts 1½" above the counter and gets a 2×8 cap that doubles as a narrow display ledge.

Module A · side section

21¾"26¾" footprint22"47"bowl sink(hidden)4×4 front leg2×8 cap4×4 wall poststructural screws tieposts to rear legs ➝
The slat wall is its own 3-post frame behind the counter, through-screwed into the rear legs and apron with structural screws. That connection is what makes the whole thing rigid. Skip the posts if the slats anchor to a fence or a wall instead.

Module A · counter top view

96"21¾"24" to sink center"burners": cast-iron burner covers or wood rounds, matte black13" stainless bowl inØ12¼" jigsaw cutoututensil crock / water zone
Trace the bowl, cut the circle ~½" smaller than its rim, test-fit. The bowl lifts out for dumping and rinsing, so there's no plumbing anywhere in this piece.

Module A cut list

PieceQtyCut sizeFrom stock
Front legs34×4 × 20½"3 × 4×4×8'
Wall posts (rear)34×4 × 45½"
Top aprons (front + rear)22×6 × 96"12 × 2×6×8'
Bottom stretchers22×6 × 96"
End + middle cross rails32×6 × 14¾"
Low shelf boards32×6 × 89"
Backsplash slats42×6 × 96"
Countertop boards32×8 × 96"4 × 2×8×8'
Cap ledge12×8 × 96"
Mini shelf (from cross-rail offcut)12×6 × 20"offcut

3 · Module B: the sensory pan table

This is the piece doing the most work in the reel: a low buffet line of five stainless steam-table pans dropped into a ladder-style top. Restaurant-supplyGN ½ (half-size) pans, 6" deep are the trick. They're cheap, indestructible, and they lift out, so the boys can dump them and I can hose them off. The deep double-2×6 skirt hides the pan bodies and gives the chunky look.

Module B · top view

82¼"16⅞"12¼"3½" (2×4 spacer)openings 12¼" × 9⅞"rim rests on the frame; test-fit your pans first
Top is a ladder: two 2×4 rails the full length with 2×4 spacer rungs between openings. Cut openings ~¼–½" smaller than the pan rim all around.

Module B · front elevation

82¼"18"2×4 ladder toppans hang 6" into the skirt cavity (dashed)2×6 skirt, two rows, front + back + ends4×4 legs, inset 2"
18" top height suits ~2–6 year olds standing.

Module B cut list

PieceQtyCut sizeFrom stock
Legs44×4 × 16½"1 × 4×4×8'
Ladder rails22×4 × 82¼"5 × 2×4×8'
Ladder spacer rungs62×4 × 9⅞"
Lower stretchers22×4 × 78"
Skirt boards (front + back, 2 rows each)42×6 × 82¼"5 × 2×6×8'
Skirt end boards (2 rows each end)42×6 × 13⅞"
Steam-table pans5GN ½ size, 6" deep, stainlessrestaurant supply, ~$15–25 ea

4 · Module C: the corner bench (optional)

The reel's L-corner is a low chunky bench, the same construction shrunk down: 4×4 legs at 10½", a 2×6 double skirt, and three 2×6 boards laid flat for the 48" × 17" seat at 12" high. It closes the corner, gives a place to sit, and works as overflow counter. A second one goes in later if the layout grows.

PieceQtyCut sizeFrom stock
Legs44×4 × 10½"1 × 4×4×8' (42" used)
Seat boards32×6 × 48"4 × 2×6×8'
Skirts, stretchers, end caps~72×6, 48" and ~14"

5 · Consolidated bill of materials

Lumber (modules A + B; add column C for the bench)

StockABC (opt.)TotalNotes
4×4 × 8'3114–5legs + wall posts; pick straight, dry stock
2×6 × 8'125417–21frames, slats, shelves, skirts
2×8 × 8'4——4countertop + cap ledge
2×4 × 8'—5—5pan-table ladder top + stretchers

Hardware and fixtures

ItemQtyNotes
Exterior structural screws #9 × 2½"5 lb (~330)all general assembly; coated or stainless
Exterior screws #10 × 3½"~60into 4×4 legs and doubled skirts
Structural lag screws ¼" × 5–6" (GRK RSS / Spax)~16wall posts → rear legs/apron; leg-to-frame
Titebond III (exterior glue)1optional but cheap rigidity
GN ½ steam-table pans, 6" deep, stainless5~12¾" × 10⅜" rim; anti-jam standard weight
Stainless mixing bowl, 13"1the sink; lifts out to drain
Cast-iron burner covers 7–8" (or wood rounds, matte black)4screw or silicone down
Wood knobs ~1¾", painted black4machine-screwed through apron so they spin
Brass cup hooks ¾–1"14–16under cap ledge, every ~6"
Stainless S-hooks8–10for pans/utensils on the slat wall
Shelf brackets (or wood corbels from offcuts)2mini jar shelf
Exterior finish: penetrating oil or zero-VOC exterior stain1 qt–1 galsee the finish note below
12" × 12" pavers or composite shimsas neededkeep legs off wet ground, level the run

Play accessories

The creator's own caption lists hers as all thrifted or retired from the indoor kitchen: stainless cups with handles (they hang on the hooks), clear canisters for "ingredients", a stock pot, whisks, serving spoons, spatulas, tongs, and baking trays. Squeeze bottles with tinted water show up in the video too.

Ballpark cost (Aug 2026, big-box pricing, varies by region)

BucketBudget: SPF/whitewood + stainPremium: cedar
Lumber (A + B)$230–300$550–700
Pans, bowl, burner covers$130–180
Screws, hooks, knobs, glue$70–90
Finish$25–60
Total≈ $455–630≈ $775–1,030

6 · Build sequence

  1. Cut everything first. Every piece is a straight crosscut on the miter saw except the sink circle and five pan openings, which are jigsaw work.
  2. Module B top. Assemble the 2×4 ladder on a flat surface, checking each opening against an actual pan before screwing the next rung.
  3. Module B base. Legs into the double 2×6 skirt box, stretchers low, then drop the ladder top in and screw down through the rails.
  4. Module A base. Build the two end leg assemblies plus the middle pair, connect with aprons and stretchers, then shelf boards.
  5. Countertop. Screw the three 2×8s down; mark the bowl, jigsaw the sink cutout, test-fit.
  6. Slat wall. Lay the three posts on the ground, screw slats and cap on flat, stand it up, lag it to the rear legs and apron.
  7. Details. Knobs, burners, hooks, mini shelf. Round over every edge (⅛–¼") and sand to 120: kids drag hands along everything.
  8. Finish. Two coats, recoat annually. Set the legs on pavers, level with shims.

7 · Decisions and options

Wood. Cedar matches the look in the reel, stays flat, and needs no pressure treatment. The budget route is SPF with a good exterior stain; it just weathers faster. Either way I'm skipping pressure-treated on the counter and the pan-table tops, because hands and "food" are on those surfaces constantly. Modern PT is fine under the legs, or the legs stay untreated and sit on pavers.

Finish. Pure tung or a linseed-based penetrating oil is the kid-safest choice and the easiest to refresh. A zero-VOC exterior stain lasts longer between coats. Film finishes (poly, paint) are out on the counter: they peel outdoors.

Water. The reel's version is plumbing-free. The bowl sink lifts out, and squeeze bottles and a dispenser jug supply the water. If I want running water here later, the pump architecture from the water table transfers straight across: a Jebao DCW-2500 recirculating out of a hidden stock-pot reservoir, through a cheap gooseneck tap bolted to the slat wall. Same trick, one project over.

Strength check. Three leg pairs under an 8-ft 2×8 top is heavily overbuilt for kid loads; adults can sit on it. The pan table's double skirt is similarly stout. The one thing to respect is the slat wall. A 47" wall of 2×6s is top-heavy on its own, so it gets lagged to the counter frame or to the fence.